Nederlands | English | Deutsch | Türkçe

Project Sports

Questions and answers about sports

How to open Gazelle Orange c7+ chain case?

5 min read

Asked by: Maria Miller

How do you remove a closed chain guard?

Quote from video: The best way to get out is just to push the clips back like this it's really easy. So at the start it can be a little bit tricky to get out. Though. And now the front part is also free.

How do you put on chain guards?

Quote from video: And bolts that will come to that a little bit later on the tools you're going to need to do this are a flat headed screwdriver. And eight mil allen key that's for taking off the cranks.

What does a chain guard do?

A gear case, also known as a chain case or chainguard, is an enclosure for the bicycle chain and sprocket assemblages commonly employed by utility bicycles. It serves to protect the cyclist from being soiled or trapped in the chain rings and tends to fully enclose the drive train.

How do I measure my bike chain guard?

Quote from video: Position. If the chain uses a master link install half of the master link this will account for the extra 1/2 inch the master link provides.

How do you put chain back on bike chain guard?

Quote from video: Also need to check that the front mech is in line with the gear on the front ring if it's in forward position on the small ring we need to move it across can then let the tension back out.

How do you clean a WOOM bike?

Quote from video: Grab your brush with the soft bristles now and a bucket of warm water if you can now's time to dip the brush in and out of the warm water. So you can scrub the bike. Clean.

Do men wear snake chains?

Both men and women wear snake chains. The thinner snake chains are typically for women and worn with pendants.

How does a chain guide work?

When you are flying through rough sections of trail, the chain will jump up and down and can sometimes work its way off the chainring. The chain guide’s job is to keep the chain inline with the teeth on the chainring so that as you continue pedaling, the chain will continue to fall in to place.

What is a chain catcher?

If you’re not familiar with the concept, a chain catcher is a length of aluminium that attaches to your front mech bolt, extending downwards to stop your chain from overshifting inwards. Its job is to get in the way. That’s all.

Can you ride a bike without a chain guard?

Even if your state doesn’t require it, it’s highly recommended that you have a chain guard on your bike. As you can see, having this protective unit on your machine has many advantages! If your chain breaks, the guard keeps it away from your leg or the tail of the bike.

Why do some bikes not have chain covers?

These chains are lubricated using vaccum pressure and the oil stays inside chain for longer. Thus the cover is not required. Also the friction is less because of O and X rings within the chain teeths. Also these chains are used in performance bikes are way durable and rugged than non O ring chains.

Is a bash guard necessary?

The industry seems to have decided that bash protection broadly isn’t needed anymore; bash guards are rarely seen on bikes with less than about 170mm of travel.

How do you take off a bike chain without the tool?

Quote from video: You can bridge the chain across two solid things and then you take yourself a punch put it on top of one of these rivets here or whatever these things are called. And try to hammer.

How do you unravel a bike chain?

Quote from video: End bring it up to the kink and grab the loop from that slack part. And just release and it comes undone just like that I'm afraid I turned it the wrong way there and I made another kink.

How does a bike chain go on?

Quote from video: If the chain is fallen off at the front chain set lift the derailleur to create slack. Then gradually feed the chain onto the teeth of one of the front chainrings.

Can you add a chain guard to a bike?

You can retro fit a chain guard to your bike. However, it can be a little complicated. Therefore, you may want to opt for using the helmet of a knowledgeable bike mechanic from a local bike shop. The best option is to choose a full chain case.

How do you put a safety chain on a necklace?

More videos on YouTube

  1. Use a pair of snipe nose pliers to open one of the jump rings on the safety chain.
  2. Attach the jump ring onto the end of your necklace.
  3. Use pliers to twist the jump ring closed.
  4. Repeat the previous steps for the other side of the safety chain.

How long should a bracelet safety chain be?

Make sure the chain is long enough so the finished design fits over the wrist as the length or opening of the bracelet will be fixed, like a bangle bracelet. With your extender chain in hand, place the last link on one end of the chain onto the cording, then finish the end capturing the chain in place.

What do you do with extra chain bracelets?

To reattach the chain, simply open the link at one side of the new chain, just the way that you did in Step 3. Hook that link through the link at the other side of the chain, then gently reverse the motions to close the link.

How do I make sure my bracelet doesn’t fall off?

Insert a pinky finger under the strings and tie them together. Inserting a pinky finger will help to ensure that the bracelet is not too tight. Stick your pinky finger under the strings and wiggle it to help loosen up the strings as needed.