Nederlands | English | Deutsch | Türkçe

Project Sports

Questions and answers about sports

How to fix the tension in these shifters?

5 min read

Asked by: Justin Hollins

How do you fix a stiff bike shifter?

Quote from video: If there was I go ahead and flush this with like wd-40. Until I got it moving freely and then spray with lubricant.

How do you loosen the grips on a shifter?

Quote from video: And just squirt a little bit and the allen wrench is going to make an opening on there for the alcohol. To get in there.

How do you fix a Shimano shifter that won’t shift?

Quote from video: And get some slack in your cables. And then just unhook the cable housing from the cable. Stop there and that'll allow you to get some slack there and shift it through the full range. Without.

What are the two types of shifters?

Today, the most common types of shifters are: Trigger. Twist/grip. Integrated brake-shifter levers (a.k.a. “brifters”)

Why is my shifter so stiff?

Not Enough Gear Oil



Once this happens, there will be damage to your transmission and it will eventually become hard to shift it. There may even be strange noises or poor vehicle performance symptoms too.” If your gears are sticky or stiff, you need to have it seen to as soon as possible.

What causes stiff gear changes?

If your car has sticky gears, it could be due to a clogged transmission filter. If you allow this to go on too long, then your pump could wear out. A clogged filter can also allow air to be incorporated into the fluid. This will cause problems with your hydraulic pressure in your system.

Why is it hard to shift gears on my bike?

If your motorcycle is having a hard time shifting gears, it could be due to a dragging clutch. This means that the clutch disk drags and fails to disengage when you press the clutch pedal. The clutch is spinning with the engine which makes it nearly impossible to change gears.

How does a grip shifter work?

When you’re just riding along, your hand rests on the grip with the inside of your hand naturally holding the Grip Shifter, which you twist backward and forward to shift. When you feel like it’s too hard to pedal and want to shift into an easier gear, you twist the shifter back.

How do you adjust a Shimano Grip Shift?

Grip Shifter



Remove the small set screw, using a hex or Allen wrench, that holds the cable in place. The cable should now move freely. Loosen the cable barrel adjuster and pull the cable end out of the housing to remove any slack. Tighten the barrel adjuster, re-attach the set screw and tighten.

How do you fix a Shimano trigger shifter?

Quote from video: So we can usually hit it with wd-40. Break it down let it dry up a little bit and then squirt some maybe some lithium grease back inside.

Why can I move my shifter but it won’t move into gear?

The real reason for a faulty gear shifter differs from vehicle to vehicle. However, the most significant probable cause is a poor construction or attachment of a flexible cable to the gear selector and transmission connection.

How do you service bike shifters?

Quote from video: It's clean as a whistle then just dry it off mop up any excess. And then. Simply put some lube on it. So some really lightweight aerosol lube with a bit of PTFE. In.

How do I change my gear 1 to 2 smoothly?

To move from first to second gear keep your hand on the gear lever, palm away from you, apply slight pressure to the left to stop the gear lever springing back to the central neutral position, and move the gear lever straight back.

Why does my car jerk from 1st to 2nd gear?

A common cause of transmission shifting issues like when your car jerks when shifting from 1st to 2nd is when there is an issue with your transmission fluid. For instance, when you have a low fluid level due to leakages or untimely fluid change.

Why does my transmission shift hard from 1st to 2nd?

If there is no oil or a low-level of oil due to leakages or the failure to change its levels, it will make manual transmission shifting hard from 1st gear to 2nd or 3rd gear. Low fluid can result in overheating and a deficiency in the creation of hydraulic pressure that is needed to engage gears.

Why is my MTB shifter so stiff?

Stiff shifter is unlikely to be the shifter or mech and most likely a cable issue – either bad routing, or stiff in the outers, or both. Worth disconnecting the cable and checking the shifter and mech move freely, then dropping the mech to the correct height to avoid shifting problems.

Why can I move my shifter but it won’t move into gear?

The real reason for a faulty gear shifter differs from vehicle to vehicle. However, the most significant probable cause is a poor construction or attachment of a flexible cable to the gear selector and transmission connection.

Why are my gears hard to shift on my motorcycle?

If your motorcycle is having a hard time shifting gears, it could be due to a dragging clutch. This means that the clutch disk drags and fails to disengage when you press the clutch pedal. The clutch is spinning with the engine which makes it nearly impossible to change gears.

Why is my bike gear stuck?

If the gears on your bike are properly indexed, each single click of the shifter will cause a single shift up or down the gears, front or rear. If you find you’re skipping a gear or that your shifting is getting stuck, then there’s a good chance you need to adjust your indexing.

How do I adjust my bike shifters?

Here’s how to do it:

  1. Step 1: Shift into the smallest gear. I also like to drop my cable tension as low as possible. …
  2. Step 2: Adjust the high limit screw, usually marked with an “H”. …
  3. Step 3: Tension the cable properly. …
  4. Step 4: Carefully shift up into the largest gear. …
  5. Step 5: Fine adjustments.


How do you know if your bike gearbox is damaged?

Chunky, hard shifting, a burning smell, a whirring, chattering, and shaking from your transmission are a few signs your gearbox is damaged.