How do I reset my hunter core? - Project Sports
Nederlands | English | Deutsch | Türkçe | Tiếng Việt

Project Sports

Questions and answers about sports

How do I reset my hunter core?

7 min read

Asked by: Monique Longoria

Resetting a Hunter X-Core is easy. To reset the irrigation controller, all you need to do is press the negative, the hand and the program keys at the same time, then use a small tool to press in the small reset button on the side of your controller. A small screwdriver or a pen will do the trick.

How do I reset my core controller Hunter?

  1. Turn the dial to the advanced features position. Press the down arrow to scroll to page two. Select ERASE ALL by pressing the “+” button.
  2. Press and hold the “+” button. The display will briefly inform you to please wait and then indicate when the reset is done. 2.666665.
  3. Where is reset button on Hunter sprinkler system?

    So okay I'm using a screwdriver you can use whatever you can and what I need to do is I need to hold down this program button and then hold this side button the reset button for three seconds.

    How do I reset my automatic sprinkler system?

    1. Turn the control dial to the “off” position.
    2. Press the “next” button to access the clear-memory feature. …
    3. Press and hold the “off” button until the display stops blinking.
    4. Turn the control dial to the “run” position.
    5. Press and hold down the “minus” arrow and “prog” buttons simultaneously.
    6. Why is my Hunter irrigation system not working?

      The most common reason your sprinklers are not watering is because the rain sensor is active. Do you have a rain sensor on your sprinkler system? If so, slide your sensor bypass switch into the “BYPASS” position (on an SRC, turn the dial into the RUN (Bypass Sensor position).

      How do I know if my sprinkler controller is bad?

      Sprinkler System Troubleshooting — 5 Signs Of A Faulty System

      1. Controller Isn’t Working Properly.
      2. Low or High Water Pressure.
      3. Sprinkler is Stuck or Won’t Come Up.
      4. Puddles on Lawn or Around Sprinkler.
      5. Uneven Spray Patterns.
      6. When to Call a Professional.


      Why is my controller not starting the watering cycle?

      Check the valve.



      Make sure the valve is operating normally by turning the solenoid 1/2″ turn counter-clockwise. Turning the solenoid will turn the valve on manually. Turn the solenoid clockwise until snug to turn off the valve. If the valve will not turn on manually, check the water supply to the valve.

      Why do my sprinklers stay on?

      One of the most common reasons for a valve to keep running continuously is the accumulation of debris in the diaphragm, which prevents the valve from closing. This video will teach you how to clean the diaphragm on your valve. The most common reason for a valve to remain on, or weep, is debris.

      How do I reset my hunter Hydrawise controller?

      WAND – Factory Reset

      1. Press and hold the WAND button for 5 seconds and Fdr will appear on the controller LCD.
      2. The module LED will turn off.
      3. Release the button when the solid amber LED appears. …
      4. Return to the online setup wizard in your Hydrawise controller settings account page to reconnect WAND to Wi-Fi.


      How do I reset my hunter X2?

      X2 – Total Reset

      1. Turn the dial to the RUN position. …
      2. Press and hold the program button.
      3. Press and release the RESET button located inside the lower wiring compartment. …
      4. When the display reads the controller station count; (e.g. 14) then DONE, release the PRG button.

      Why is my sprinkler system not turning on?

      When the sprinkler zones do not turn on at all, it is generally a problem with the electrical signals running from the controller to the valve solenoids. More rarely, it is caused by a faulty valve that needs to be rebuilt or replaced.

      How do you fix a sprinkler valve that won’t turn on?

      If the controller is activating other zones. Okay we know it has power. But if the entire system won't activate make sure to verify power at the controllers outlet with a test light or voltage meter.

      How do I manually start Hunter Pro C?

      You just hold down the right arrow up here in this new style face pack. And you let go of the arrow.

      How do I manually turn on my sprinkler system?

      And these are all manual valves down inside here you see this little tiny square. Spicket if you turn that counter clockwise a quarter of a turn.

      How do I test my Hunter Pro C sprinkler system?

      To initiate the test program:

      1. Press and hold the PRG button. The station number will be flashing.
      2. Press the or button to scroll to the station you would like the test program to start with. Use the and buttons to set a run time of up to 15 minutes. …
      3. After a 2 second pause, the test program will begin.


      How do you manually run a sprinkler Hunter?

      You can also activate all stations to water without using the dial.



      X-Core – One Touch Manual Start and Advance

      1. Hold down the arrow (>) button for 2 seconds. …
      2. This feature automatically defaults to program A. …
      3. The station number will be flashing. …
      4. Press the arrow (>) button scroll to the station you wish to begin with.


      How do I turn on Hunter node manually?

      The controller will display a countdown and activate desired station.



      1. To manually activate a program, press and hold the right arrow button until the. icon is displayed, then quickly press the PRG button. …
      2. To stop the Manual watering cycle press the minus button until the time is reduced to zero.
      3. Press the.


      How do you program a sprinkler system?

      Start times. So the start water and start watering times is for what time of day you want to come on.

      What is the easiest sprinkler controller to program?

      • Our pick. Rachio 3. Set it and forget it. …
      • Runner-up. RainMachine Touch HD. For local control. …
      • Also great. Orbit B-hyve XR. Better coverage for bigger yards with smaller budgets. …
      • Budget pick. Orbit B-hyve Smart Indoor Irrigation Controller. Style and simplicity for less.
      • Is there an app for Hunter sprinkler system?

        Hunter Hydrawise



        Remote access is possible through either the Hydrawise app (iOS or Android compatible devices) or online through their cloud software. Key product features include: Predictive Watering Adjustments based on web-based weather data brings up to 50 percent in water savings.

        How do I set the time on my hunter sprinkler system?

        We can use the right arrow or the left arrow to scroll backwards or forward through the different choices. The PRG button is to be changed from programs A to B to C.

        How do I change the time on my hunter node?

        To set the time and date on the node press the center button, simply scroll through the choices using the left and right arrow buttons and adjust the displayed item using the plus and minus buttons. Push the button until the icon is displayed. All 4 digits will be displayed representing the year.

        How long should I water my lawn?

        It is ideal to water lawns about one inch of water per week. To determine how long you need to water to get one inch, place a plastic container in your yard and set a timer. On average, it will take 30 minutes to get a half inch of water. So, 20 minutes, three times per week will give a lawn about an inch of water.

        What does Epsom salt do to lawns?

        Epsom salt is an organic compound that is full of beneficial minerals for lawns. Iron in Epsom salt, for example, helps grasses to grow healthy and strong. Meanwhile, the magnesium in Epsom salt balances the PH level in your grasses so that it doesn’t become too acidic.

        Is it bad to water grass at night?

        “A wet lawn at night is the perfect condition for fungus to grow. Along with cutting grass too short, watering at night is about the worst thing you can do to a lawn.” As a general rule, you should water long enough to moisten the soil down to about 6 inches, which is the average depth of a healthy grass-root system.