Why does my Hayward Pool Vac go in circles?
4 min read
Asked by: Peter Kundu
Your pool robot is going in circles because its feet are unevenly worn, the hoses are tangled, the swivels are jammed, or there’s a broken belt. These issues cause the pool cleaner to lean to one side, making it rotate without moving straight.
Why is my pool vacuum moving in circles?
Your first issue is to resolve the problem of the cleaner getting stuck or going in circles. This is most likely caused when pool cleaners are left in the pool 24/7. When the water is cold or cools off from a warm day, the plastic in the hose gets a memory and curls slightly.
Mar 9, 2008
Why does my Hayward pool Vac turn in circles?
WRITTEN BY: Inyo Pools
Is it spinning in circles or getting stuck in corners instead of going around the pool? There are an assortment of gears and moving parts inside the Navigator that need to be checked and replaced now and then. Sometime, it’s just debris interfering with the movement of the gears.
Why does my pool vacuum keep going on its side?
Cleaner keeps falling on its side.
Check to make ensure that the hose connected to the head is the leader hose (the section of hose with the grey cuff). A connector hose attached at this point can cause this situation. Check to make sure the leader hose is in good condition.
Why does my pool cleaner stay in one spot?
If your Kreepy Krauly is often stuck at one side of your pool there are two potential fixes. If the hose is too short then buy another line and have it extended out enough to cover the pool. On the other hand, if it is constantly being coiled then relaxing it or changing how you keep it stored will fix that problem.
Feb 16, 2021
How do I adjust my Hayward pool vacuum?
So you can address the suction of the Hayward for the skimmer by turning this blue dial here. And that will increase or decrease the suction.
How do you adjust a pool cleaner?
You want to push firmly. So it stays. In. You want to pull the cleaner to the side of the pool. You want to look at the right tire that's one that doesn't rotate. You want to get the hump.
How long does a Hayward pool vacuum last?
Quick Answer: Typical Lifespan of an Automatic Pool Cleaner
On average, you can expect your automatic pool cleaner to last around 4 to 5 years.
Why is my Hayward pool cleaner moving slowly?
If your Hayward pool vacuum becomes too slow to clean your pool effectively, the vacuum likely has a blockage or the shoes and wings need to be replaced. Shoes and wings have wear indicators for determining when they require replacement.
How do you repair a Hayward Navigator pool cleaner?
First turn the navigator on its back then insert a screwdriver between the shoe and the pod to pry the shoe. Off. Next dip a new shoe in the water for lubrication.
How do you keep a pool vacuum from getting stuck in the corner?
It's got gears in here and they operate to do that. You're going to keep a gear spinning in there. And that's what causes being device actually work and twist the hoses.
Where do I put the weights on my pool cleaner?
For pools 4′ deep or less, use 1 hose weight 4″ to 12″ from the cleaner. For pools of 4-7′ deep, use 2 weights, one 4″ to 12″ from the cleaner and one 6′ from the cleaner. For pools from 8′ to 12′ deep, use a third weight, placed 10 ft. from the swivel end of the cleaner.
Aug 9, 2017
How do I increase the suction on my pool vacuum?
Just give that a bit of a clean-out. Make sure that the hole is facing the in pipe to pump you check your o-ring. That's so that's make sure it's there secure the lid back nicely on the pump.
Why does my pool vacuum lost suction?
Rule out the obvious causes of poor vacuum first. Make sure the water level in the pool is sufficient and air is not being sucked in through skimmer inlets. Add water to the pool to submerge the skimmers if necessary. Verify that the pump strainer basket and the skimmers are free of debris that may obstruct water flow.
Why doesn’t my pool vacuum have suction?
Verify that the vacuum hose is firmly inserted into the inlet port at the skimmer; then inspect the hose for cracks or holes. The skimmer filter is dirty. Pull out the filter basket and check for debris that may be interfering with water flow to the pool pump. Air is getting into the pump through the pump cover.
