Where is the serial number on a power pole? - Project Sports
Nederlands | English | Deutsch | Türkçe | Tiếng Việt

Project Sports

Questions and answers about sports

Where is the serial number on a power pole?

4 min read

Asked by: Norma Stewart

Where is the power pole serial number?

Power-Pole® CHARGE™ Marine Power Management Station



The serial number is located on the top of the unit. For models pre-2022, the serial number is located on the bottom of the unit.

How do you pair a remote with a power pole?

To begin pairing locate the hpu you want to pair to and press and hold the orange program button for 3 seconds. The led will turn solid green and the hpu will beat.

What are the different parts of a power pole?

When you look at the power poles in your neighborhood, you’re likely going to see a combination of the following:

  • Primary wires. …
  • Insulators. …
  • Crossarm. …
  • Lightning arresters. …
  • Pole ground wire. …
  • Transformer. …
  • Neutral line. …
  • Secondary service drop.


How deep will a power pole go?

10ft deep

Depth – Power-Pole has a maximum deployment of 10ft deep for the most effective stopping and holding vs. 12ft.

How do you update power poles?

And you can search the letter C – monster. When you search that you'll see the official power pool sea monster app and you can download that app once you download the app you can then open the app.

How do you manually lift a Power-Pole?

STANDARD MODE To raise or lower your Power-Pole, press and hold either the UP or DOWN button on the Dash Switch. The anchor will only continue to move as long as you press the button.

What fluid goes in a Power-Pole?

Green Marine hydraulic fluid

Power-Pole has developed Green Marine hydraulic fluid to provide the performance of a petroleum product without the harmful effects. This ISO-32 fluid is ideal for use in Power-Pole systems, trim tabs, jack plates, tilt and trim rams, hatch lifters and more.

How do you prime a Power-Pole?

STEP 1 Connect power to the HPU. STEP 2 Manually place the Power-Pole Anchor in the deployed position. STEP 3 Using the Wireless Dash Switch set to SLOW speed, hold the DOWN button until the RED LED on the dash switch stops flashing and the pump stops running. (Approximately 20 sec.)

How do you fix a Power-Pole?

This they come apart pretty easy uh a trick to putting these back together would be to have a little grease so that you can grease these bushings. And hold them in place as well.

How long does it take to fix a broken electric pole?

How long does it take to replace a pole? Estimates vary greatly depending on the location and complexity of the replacement. General estimates range from 8 to 18 worker hours for a low-difficulty replacement and 20 to 75 worker hours for a high-difficulty replacement.

When should power poles be replaced?

Moisture from driving rain, whipping winds, and flash floods are capable of doing a number on material left to the elements. It’s quite a feat that the average lifespan of a utility pole is 30 to 40 years.

How long does a utility pole last?

around 50 to 60 years

Many utility poles are several decades old



Most power poles are much older than their useful life expectancy, which is likely somewhere around 50 to 60 years. But some of them are much older. Metal and concrete poles can last much longer than wood, but eventually all utility poles need to be replaced.

How much does a 30 foot power pole weigh?

The density of pine is ~30 lbs per cubic foot, so this hypothetical pole weighs 30 * 24 = 720 pounds.

How is a utility pole replaced?

The buried part of the broken pole is usually pulled out with the hydraulic lift on a truck. Sometimes it’s necessary to dig a new hole. Dirt is backfilled and tamped down with hydraulic equipment. The power lines are then lifted back into place and mounted on the new insulators.

How long do steel utility poles last?

50-80 years

The initial cost is a hurdle which many utilities have overcome by looking forward to the long term and overall life cycle of steel poles versus wooden poles. Traditional wood poles have a life-span of approximately 30 years while steel poles often remain in use anywhere from 50-80 years.

What are metal power poles made of?

Tubular steel poles are typically made from 11-gauge galvanized steel, with thicker 10- or 7-gauge materials used for some taller poles because of their higher strength and rigidity.

What are the disadvantages of steel poles?

Disadvantages Of Steel Utility Poles



Steel is subject to the corrosive effects of chemicals and pollution. Early in the manufacturing of steel utility poles the metallurgical processes produced a type of steel that was resistant to corrosion.

How much does a steel pole weigh?

approximately 450 pounds

The average steel distribution pole (40 foot, Class 4) weighs approximately 450 pounds, and is at least 30 percent lighter than a wood pole.

How much does a 20 ft power pole weigh?

How much does a 20ft light pole weigh? Net weight: 98 lbs.

How much does a 25 foot utility pole weigh?

364 lbs

25-ft PG&E-Approved Class 5 Utility Pole. Approximate weight: 364 lbs.