What is Deco seal? - Project Sports
Nederlands | English | Deutsch | Türkçe | Tiếng Việt

Project Sports

Questions and answers about sports

What is Deco seal?

5 min read

Asked by: Tony Green

Deco Seal is a 100% water-based acrylic membrane designed to waterproof and protect concrete foundation walls from hydrostatic water pressure. These can be, Poured, ICF, Precast, or Block (parged/non-parged) foundation walls.

What is Deco seal used for?

DECK-O-SEAL is used for caulking and sealing joints subject to concrete movement to provide a firm, flexible, weather-tight seal. It is ideal for sealing joints in and around swimming pools, and is applicable for both interior and exterior use.

How long does DECK-O-SEAL last?

1- year

1) DECK-O-SEAL kits (Pour grade,125, two-part GUN GRADE and 150) have a 1- year shelf life from date of manufacture. 2) DECK-O-SEAL ONE STEP caulk has a 6-month shelf life from date of manufacture.

How long does it take Deco seal to dry?

How long does it take for the DECK-O-SEAL to cure? For DECK-O-SEAL Two Part, the material is tack free in four hours and cures in 24 hours at 77ºF. For DECK-O-SEAL ONE STEP, the material is tack free in 24 hours and cures in 5 to 10 days.

How do you remove Deco seals?

Remove old DECK-O-SEAL by following these steps:

  1. Get a linoleum knife or a razor.
  2. Run the blade of the knife down each side of the sealant up against the concrete edge.
  3. Pull the old sealant.
  4. Clean any remaining sealant off using a wire brush or grinder being careful not to damage the finish on the deck.

How much does DECK-O-SEAL cost?

The cost of this is $5.50-$6.00 per linear foot. The complete job can usually be completed within one day and the product usually dries within 24 hours in normal conditions.

How much does it cost to caulk a pool?

Cost to Caulk a Pool? Prices for professional pool expansion joint caulking runs $5.00 – $8.00 per linear foot. Measure or add up the perimeter of the pool to figure your price. The range in price depends on the width of the joint, which is usually 1/2″ – 1″, or regional differences in pricing.

How do you remove old pool caulk?

Start by removing old caulk by slicing it off close with a sharp razor knife. If debris or soils have filled the joint, use a pressure washer to remove. Insert foam backer rod in areas where it is missing, to an even depth. Load a Vulkem cartridge, snip the tip, and squeeze into the joint.

How do I remove caulk from my pool?

I decided to replace it myself with some simple tools i didn't have a powered cutting tool but i found a carpet or linoleum knife worked well to cut out the original materials.

How much should I pay for caulking?

Cost to Caulk Perimeter Of Home

Item details Qty High
Unused Minimum Labor Balance of 2 hr(s) minimum labor charge that can be applied to other tasks. 0.0 h $0
Totals – Cost To Caulk Perimeter Of Home 125 FT $512
Average Cost per Linear Foot $4.09

How often should you re caulk a shower?

approximately five years

As a general rule, caulk should last approximately five years. There are a number of variables that will determine the actual length of time between replacement, including: Type and quality of caulk used.

Do plumbers replace caulking?

If all you need is some caulking work done, it’s a straightforward enough job that a handyperson can take care of it. But, if you need extensive caulking work done or are trying to do other work along with the caulking, such as a complete overhaul of your bathroom fixtures, then you should consider hiring a plumber.

How much should I charge to caulk a bathroom?

For indoor jobs, such as sealing around a bathtub or shower, the national average cost is $110–280. Exterior caulking the perimeter of a 2,000-square-foot house can cost $750–2,000, or about $2–4.50 per linear foot. The time required to complete a caulking job usually depends on the area that needs sealing.

How much should I charge to grout a shower?

Your average-sized shower could cost anywhere between $565 to $1,750 for a full regrout, with prices hinging on the type of grout as well as how much old grout needs to be removed.

How much does it cost to have someone re caulk shower?

You will usually pay for whatever the hourly rate would be. If you pay the hundred you might find yourself a handy man for life! I would pay probably $35.00- $50.00 with caulking provided.

How do you caulk a bathtub or shower?

The straightforward process follows these steps:

  1. Remove any old strips of caulk in the shower.
  2. Use painter’s tape create a guide for the new caulk line.
  3. Apply either silicone or latex caulk with a caulk gun, or squeeze the product straight from the tube.
  4. Wipe along the caulk line with a wet finger to remove any excess.

Can I caulk over old caulk?

People often ask, “Can you caulk over old caulk?” but it may be more important to ask, “Can you caulk over cracked caulk?” Generally, caulking over old caulk isn’t recommended. Removing the old caulk and replacing it with a new bead of caulk instead usually creates a better seal.

What is the best caulk to use around a bathtub?

Silicone and latex are the two best choices for caulking a bathtub. Silicone adheres best to slick, nonporous surfaces such as glass, ceramic tile and metal. Latex is better for uneven, porous or mismatched surfaces such as stone tiles or wood trim near the base of the tub.

Can you caulk over grout?

Caulking over grout is only a temporary fix because caulk forms a poor bond with the more porous grout. Whether it takes a few months or a couple of years, the caulk will start to peel off the grout. Caulk over grout will peel off over time because caulk will not bond well with grout.

Can I use silicone instead of grout?

Grout is a hardwearing emulsion but should only be used between joints of the same plane. This means any corners or bends that your tiles and fittings encounter should be handled with silicone instead. This is because grout is not flexible enough to withstand any structural movement. It is also not entirely waterproof.

Why is my tile grout cracking?

If you or your installer didn’t use enough thinset when you installed your tile, then there’s a chance there wasn’t enough of an adhesive for the grout to cling to. As a result, gaps and cracks will occur. Water Interference During Drying Occurred.