What is a PVC spigot fitting?

Asked by: Steven Maddocks

Definition. A spigot is generally the male end of a PVC pipe fitting, which connects by attaching inside the other PVC pipe or joint. So, essentially, a spigot connects two PVC pipes or joints. Spigots can be used in different PVC pipe-fitting applications.

What does spigot mean in PVC fittings?

The end connection of a fitting that is to be assembled into another fitting is called the “Spigot.” The spigot end of a fitting has the same outside diameter as pipe. The common female connection of PVC fittings is referred to as the socket or hub, and the spigot end of a fitting can be inserted into a Hub or Socket.

What is a spigot fitting used for?

A spigot fits inside a socket, so it is the same size around as regular pipe. When you need to attach a fitting to another fitting, you use a spigot end. In their function, sockets are the female and spigots are the male. Spigot fittings are often called street fittings.

What are spigot joints?

A spigot joint is a type of pipe fitting that is inserted into another pipe fitting. The spigot end typically has the same outer diameter as the pipe and is usually fitted into another larger-diameter joint called a bell.

What are PVC fittings?

These fittings are designed to change the end type of a pipe, allowing it to connect to fittings and pipes of many sizes. They can have threaded or slip socket ends to connect to an endless variety of pipes and fittings. Adapters can be either male- or female-threaded, as well as socket or spigot.

What is the difference between spigot and faucet?

A spigot is the opening from which a liquid or gas flows. A tap or a faucet is the controller which regulates whether flow occurs, increases decrease or is stopped. In a bath tub, one opens (or closes) the faucet so water will flow (or stop) from the spigot.

What is spigot and socket joint?

Spigot & Socket joint:- This



type of joint is commonly used in case of cast- iron-pipes. For the construction of this joint the spigot or normal end of one pipe is centred into the socket of the other pipe. Hemp yarn is then wrapped around the spigot, leaving unfilled the required depth of socket for lead.

What is spigot coupling?

Into a socket end PVC pipe has spigot ends and must connect the socket connections on both ends PVC fittings have either connections. And allow connection to either PVC pipe or another PVC.

How do you put a spigot on a PVC pipe?

So go ahead and put the teflon tape. On. You want to make sure that you thread the teflon tape the same way that you're going to be screwing on the under the pvc.

What are the different types of PVC fittings?

What Are The Different Types of PVC Couplings?

• Full Couplings.
• Half Couplings.
• Reducing Couplings.
• Compression Couplings.
• Slip Couplings / Repair Couplings.

What are CPVC fittings?

Chlorinated Poly (Vinyl Chloride) (CPVC) is a thermoplastic pipe and fitting material made with CPVC compounds meeting the requirements of ASTM Class 23447 as defined in ASTM Specification D1784. CPVC applications are for potable water distribution, corrosive fluid handling in industry, and fire suppression systems.

What is PVC ball valve?

PVC (PolyVinyl Chloride) ball valves are widely used plastic shut off valves. The valve contains a rotary ball with a bore at the center. By rotating the ball a quarter-turn, the bore can be aligned inline or perpendicular to the piping to open or block the medias flow.

Are PVC ball valves any good?

PVC ball valves are an excellent choice in a wide range of plumbing applications with different options for maintenance and high temperature. Ball valves are also available in Brass and Stainless Steel so there is a ball valve for every application where the flow of water needs to be controlled.

How long do PVC ball valves last?

about eight to ten years

Using the latest and greatest ball valve in your plumbing can help save more water. It also helps you save money while helping the environment. A ball valve life expectancy is about eight to ten years.

How does a ball valve work?

A ball valve is classed as a quarter-turn shut-off or isolation valve that controls the flow of a liquid or gas by way of a spherical ball with a hole bored through the centre and held into the valve body by two identical seat seals. Once fitted the valve is turned 90°, the valve opens or closes.

When would you use a ball valve?

Ball valves are more effective at forming a tight seal and have more reliability and longevity than gate valves, but tend to be more expensive. They are often used for shutoff and control applications. Because ball valves can open and close immediately, they are more likely than gate valves to cause water hammer.

What are the advantages of a ball valve?

Advantages Of Ball Valves

• They provide leak-proof service,
• Open and close quickly,
• Compared to gate valves, they have very small dimensions,
• Compared to gate valves, they are lighter,
• The multi designed flexibility does not exist in the Gate or Globe valve, and hence it lowers the amount of valves needed,

What is the difference between globe valve and ball valve?

The main difference between ball and globe valves is the way they close. Ball valves have a stem and ball, which turns horizontally, and are commonly referred to as “rotational” valves. Whereas, globe valves have a stem and plug, which strokes linearly, and gives them their other name of “stroke” valves.

Why is a globe valve called a globe valve?

A globe valve regulates flow in a pipeline. It is used to control or stop the flow of liquid or gas through a pipe. Globe valves are named for their spherical body shape with the two halves of the body being separated by an internal baffle.

Are globe valves directional?

Globe valves are considered to be directional and must be installed with the pressure side or inlet under the seat. The valve must be installed in relation to the media flow as indicated by the flow direction arrow marked on the valve body.

What is the difference between a gate valve and a ball valve?

The main difference between ball valves and gate valves



While gate valves open by lifting a round or rectangular gate out of the path of the fluid, ball valves have a stem and a ball that turn horizontally. This is why ball valves are often referred to as a rotational valve.

What does a gate valve look like?

It is only half open. So this is in the throttled. Position the problem with this is that firstly the amount of flow through the valve is not proportional to the amount that this gate has traveled.

Can you use a ball valve for water?

Also called “shut off valves,” ball valves are the only way to immediately shut off the flow of water. Gate valves are incapable of immediate redirection. With the exception of 3-way ball valves, machined stops prevent most ball valves from moving more than 90 degrees.