Quick Release vs Thru-axle specifications when buying wheels
5 min read
Asked by: Darlene Lanford
How do I know what size thru axle I need?
For this reason, thru-axles should be measured by overall length. Depending on the thickness of the dropouts, total length is usually 20-30mm longer than OLD. The most common front thru axle OLD dimensions are 100 mm, 110 mm, and 150 mm for front axles and 130mm, 135mm, 142mm, 148mm, and 197mm for rear axles.
Are thru axles better than quick-release?
1. Thru axles are safer– This is probably the biggest benefit for the average cyclist. Thru axles improve safety by making it nearly impossible for the front wheel to come out of the dropouts while you’re moving. The dropouts can’t lift off of the axles vertically because they have holes instead of a u-shaped slots.
What is standard thru axle size?
Front thru-axle standards
The standard size for thru-axle forks on mountain bikes used to be 15mm x 100mm, with 20mm x 110mm used mainly on downhill and freeride bikes. For trail, XC and enduro bikes that’s largely changed to the newer Boost thru-axle standard, which increases the front axle length to 110mm.
Can you use a quick-release to thru axle?
Quote from video: That allows you to use a quick release skewer. On a thru axle. Wheel. It works very simply i know some other brands make these basically all that you have to do is slide this adapter into the hub.
How tight should thru axles be?
How tight should my thru axle be? Typically, thru axles should be tightened to 12-15Nm (Newton Meters) of torque. This is just enough torque to secure the axle so it does not come loose while riding. You should never tighten your axle as tight as possible.
Should you grease thru axle?
By applying grease to the threads, you not only help avoid rust and corrosion, you will also make it a lot safer and easier to remove and install your wheels. Applying grease to the actual axles itself is less important, as your wheels rotate on the bearings.
Do I need a thru axle?
Thru axles provide a stiffer ride, which can be beneficial in both the front and rear of a bike. In mountain bikes in particular, this allows for more torque and less flex for your whip. So, if you have a thin, 5mm rod, then you have a skewer. If you have a 12mm threaded piece, then you have a thru axle.
Can you use quick release on disc brakes?
In the case of the mechanical disc brake you don’t need to worry about anything. You can open the quick release and remove the wheel with no other issues. For hydraulic disc brakes, you only need to take care not to squeeze the brake lever if the wheel is not in place in the bikes caliper.
How do I know if I have a thru axle?
Quote from video: This is a hub the hub which measures the space between the dropouts. But all through axles are actually longer than the hub. Way. The few axle is longer because it has to go through the hubs and each
How do I know what size quick release skewer?
Diameter: the skewer must fit inside the hollow hub axle. You may measure either the inside diameter of the axle, or the diameter of the present skewer. Most axles use a 5mm thick skewer. Skewers for wheels made for suspension forks may be 9mm (front) and 10mm (rear) in diameter.
What does 12×142 mean?
12 mm is the axle diameter, 142 mm refers to overall shoulder to shoulder width of hub (end cap to end cap) Cassette and disc rotor are in the exact same relation to the hub’s centerline as a standard 135 mm QR hub.
How do you fit through axles?
Quote from video: If you need to change the finished position of the lever. You can adjust the axle net if the axle nut has a retention cap use a small allen wrench to remove the screw and plate.
What happens if you over tighten thru axle?
Keeping the axle under-torqued is dangerous, and over-torquing it might damage the fork/frame dropouts. A proper solution would be to adjust the position of the brake caliper itself relative to the disc.
How do you torque a through axle?
Quote from video: So you want them tight. But not too tight. If they are too loose you will actually feel the wheel wobbling around but you really don't want to over tighten them because potentially.
How tight should wheel skewers be?
Quote from video: Похожие запросы
How do you fit through axles?
Quote from video: If you need to change the finished position of the lever. You can adjust the axle net if the axle nut has a retention cap use a small allen wrench to remove the screw and plate.
Are thru axles interchangeable?
Because thru axles are a relatively new development invention, there is currently no industry standard. Countless different manufacturers produce their thru-axles to different specifications, making it impossible for Tailfin to make a single thru axle that will suit every bike.
How do you measure a rear axle?
Quote from video: With the semi float a key you're going to take your tape measure from the outside face of the flange.
How do you determine the thread pitch of a thru axle?
To identify your bikes thru axle thread pitch simply count the number of threads within a 10 mm section. If you are unable to identify the thread pitch we recommend contacting the bike frame manufacturer.
What does 12×142 mean?
12 mm is the axle diameter, 142 mm refers to overall shoulder to shoulder width of hub (end cap to end cap) Cassette and disc rotor are in the exact same relation to the hub’s centerline as a standard 135 mm QR hub.
How important is rear thru axle?
Thru-axles increase the rigidity of the wheel-frame interface and allow more accurate wheel placement. This is particularly important for brake discs, where small pad clearances mean that a slight misalignment will cause rubbing. They also eliminate the risk of the wheel coming loose from the quick-release dropouts.