Is my rear shifter broken? Ultegra 6800 shifter, 11 speeds, 9 clicks, only 8 causing cable tension change

Asked by: Christina Armstrong

How do I fix my Shimano shifter?

Quote from video: So we can usually hit it with wd-40. Break it down let it dry up a little bit and then squirt some maybe some lithium grease back inside. There.

How do you tighten Ultegra shifters?

Quote from video: That's clockwise and it shortens this gap here let me turn it back. And you're clockwise the gap gets larger. You just keep turning it until it stops moving. And then just stop turning the screw.

How do you fix a Shimano STI shifter that won’t shift?

Quote from video: And get those paws all lubed up and then it'll start working then just go ahead and model on the bike and you're all set.

How do you use a Shimano STI shifter?

Quote from video: Now with most sti's shamanic. Ones anyway the whole brake lever will move in order to shift the gear. And then inside it there is another lever that will shift the gears in the opposite directions.

How do you lubricate a Shimano shifter?

Quote from video: Use an evaporative degreaser like white lightning clean streak to remove the grit and dried up grease that is accumulated in the shifter mechanism.

How do you fix a shifter on a road bike?

Quote from video: It's safer like the plastic parts in there and so it's a spray can and I'll just spray this in I'm going to flood the inside of the shifter with it. And again start working the mechanism.

How do I adjust the tension on my rear derailleur?

Use the barrel adjuster to fine-tune its position. Turning the adjuster anticlockwise increases tension on the cable, bringing the derailleur closer to the wheel. Clockwise decreases the tension, moving it back towards the frame.

How do you adjust the tension on a bike cable?

Quote from video: So what you want to do is first shift your bike into the smallest gear releasing all of the cable tension. And you'll feel that it's quite loose. Here. Once you've done that.

How do I tighten my gear cable?

Quote from video: What you want to have is always in effect the opposite. So you want a millimeter gap between the inside of the trailer here and the chain there. So again there's an H screw.

How do you change a Ultegra shifter cable?

Quote from video: You're looking at the front of the shifter there. If you just depress the brake to open it up you'll see the hole there just there put the cable through. There. Then just close the lever slightly.

Why can I move my shifter but it won’t move into gear?

The real reason for a faulty gear shifter differs from vehicle to vehicle. However, the most significant probable cause is a poor construction or attachment of a flexible cable to the gear selector and transmission connection.

Why are my bike gears not working?

This is usually caused by an overly tight gear cable or the low limiting screw that needs adjusting. You can test this by shifting to the lowest gear and seeing if your front derailleur is in line with the smallest chainring. If not, try adjusting the limiting screw. Alternatively, your gear cable may be too tight.

How do I test my Shimano shifter?

Quote from video: In this video I'm going to show you where model numbers are on Shimano. Parts. So here's a dual control leaver it's an old one you peel back the boot and on this one it is right there st – 2 3 0 0.

Can I spray WD40 on my shifter?

1 Answer. You can spray WD40 on it and it might make it looser for a couple of days. Try some real oil or white lithium grease for longer lasting lubrication.

Do Shimano shifters wear out?

Yes, they do wear out -some faster than others- but you should be fine sticking with what you have.

How do you fix a sticky shifter?

Quote from video: Into it wd-40 dissolves the old grease and with a slight film of new grease. Into the shifter.

Why are my bike gears not changing?

This is usually caused by an overly tight gear cable or the low limiting screw that needs adjusting. You can test this by shifting to the lowest gear and seeing if your front derailleur is in line with the smallest chainring. If not, try adjusting the limiting screw. Alternatively, your gear cable may be too tight.

Why is my gear shift sticky?

If your car has sticky gears, it could be due to a clogged transmission filter. If you allow this to go on too long, then your pump could wear out. A clogged filter can also allow air to be incorporated into the fluid. This will cause problems with your hydraulic pressure in your system.

How long is Shimano warranty?

Warrants to the original retail purchaser that the SHIMANO bicycle division product for which they received this warranty, is free from a defect in material and workmanship for a period of two years and their DURA-ACE and XTR components are covered for a period of three years from the date of original retail purchase.

Do Shimano reels have lifetime warranty?

Shimano’s limited lifetime warranty has always been limited to protecting the rod against non-conformities in material and workmanship. While frequently misunderstood, the limited lifetime warranty has never been an unconditional warranty that covers normal wear and tear, accidents or abuse.

What does Shimano warranty cover?

Shimano warrants to the original retail purchaser that the Shimano bicycle division product for which they received this warranty, is free from non-conformities in material and workmanship for a period of two years*; and their DURA-ACE and XTR components are covered for a period of three years* from the date of