How to remove a lock ring if there is no cassette?

Asked by: John Long

How do you remove a cassette without a cassette tool?

Quote from video: Like a flathead screwdriver.

How do you remove a stuck lock ring?

Quote from video: So just take some pliers or channel locks or whatever and just kind of wedge it up onto the one tooth of the cog.

How do you remove a sprocket lock ring?

Quote from video: Now take your lock ring removal tool slip it over the axle. And down into the splines. And lock ring cap just like that. And then go ahead and reinstall.

How do you remove a Shimano lock ring?

Quote from video: And it just fits right into the lock ring into the splines. So if you were to put your wrench on now to try to loosen the lock ring. The rear cassette just ratchets like it normally does.

How do I know if I have a freewheel or cassette?

Quote from video: But here we have a reliable rule of thumb. Let's review it again as we spin the cogs counterclockwise a cassette stool fitting will also spend but on a freewheel.

How do you remove a freewheel without a tool?

Quote from video: And I'm gonna use a punch and a hammer. I'm gonna fit the punch into the little dimple and then using the hammer I'm going to tap this clockwise. And get it to rotate.

Can you over tighten a cassette?

Can You over-Tighten a Bike Cassette? Yes, you can overtighten a bike cassette and this usually doesn’t end well. If you go way above the torque recommended for your cassette lock ring, you would be overtightening it. This is why using a torque wrench is advised when tightening your cassette.

How do you get a stuck cassette out of a rear wheel?

Quote from video: And in the end if you just keep doing it by moving it round a bit at a time hitting it just tapping. It.

How do you remove a rear cassette?

Quote from video: Because of this the tool may slip out under heavy torque to prevent this remove the quick-release skewer nut and spring engage the lock ring tool and reinstall the nut snug.

How do you remove a rear cassette without a chain whip?

Quote from video: It jab it through either side of a quick link in the smaller harder to get through ones doesn't really matter it's fraying. So long as it's through right.

What is a cassette lock ring?

The lockring is designed to hold the cogs of the cassette in place on the hub.

How do you remove a freewheel?

Quote from video: Turn the tool counterclockwise. It may take a good bit of force to loosen the freewheel from the hub. After it's loose remove the axle nut or skewering. That continue to unthread the freewheel.

What is the difference between a freehub and a freewheel?

Freewheel vs Freehub – Thread Differences



One of the main difference is that freewheels typically have a threaded hub. Bikes equipped with cassettes do not have a threaded hub, but instead, slip onto the hub with splines. But the differences, without getting too technical — go deeper than that.

How do I convert my cassette to freewheel?

Quote from video: The cassette is installed by sliding onto the hub. And then locking in place using this lock. Ring. So you may be wondering what's the advantage of one over the other.

What is the difference between Freecoaster and cassette?

Quote from video: The basic internals on a free coaster hub is your clutch. Which engages along a spiral thread mechanism. Where a cassette relies on a call and spring mechanism.

What tools do I need to remove a cassette?

In order to remove and replace your cassette, you need to unscrew this lockring. You’ll need three tools to do this: a chain whip, a cassette lockring remover and a large adjustable crescent wrench.

How do you remove a tight cassette?

Quote from video: Put one chain whip on the outermost cog. And the other on the larger cog that is attached to the cassette. Spider rotate. The outer cog counterclockwise.

How do you remove a cassette?

Quote from video: On these style chain whips engaged the fixed section of chain and wrap the free piece around the same sprocket. Turn the remover counterclockwise. Using a large adjustable wrench or a one inch wrench.

How do you remove old cassettes?

To remove the cassette, hold it from spinning using a chain whip. Insert the lockring tool (use the FR-5 series), and turn the tool counter-clockwise. The locking ring will unthread from the freehub and the cassette will lift upward. To install the cassette, lubricate the threads inside the cassette stack.

How do I convert my cassette to freewheel?

Quote from video: The cassette is installed by sliding onto the hub. And then locking in place using this lock. Ring. So you may be wondering what's the advantage of one over the other.

How do you remove an old cassette freewheel?

Quote from video: You put your big wrench. Honestly I find this is easier to do like if you're standing vertically with the wheel and pushing down but it's just a demonstration. And then ah apply a lot of torque uh.