How to adjust rear hub on Giant ATX 2?

Asked by: Brian Bjorke

How do you tighten a rear hub?

Quote from video: Screw the cone in or out to tighten or loosen the bearing on the freehub. Make small adjustments and check the bearing between.

How do you service a giant rear hub?

Quote from video: Set head straight for the ultrasonic cleaner. And then these caps are just dust covers i think it depends on whether you've got through axles or quick releases to which caps you would have on these.

How do you fix a loose hub?

Quote from video: It towards touching and maybe back it off just a hair. And then i'm going to put the washer on here. And then take the lock nut. On here and then tighten this down.

Why is my back wheel wobbling on my bike?

One of the most common causes for a rear-wheel wobble is misaligned spokes. If your spokes are not evenly tensioned on either side of your bike, then this can cause some serious problems. Have any one of these spokes become too loose or too tight and you’ll likely see a wobbling wheel while biking down the road.

What hubs do giant use?

Giant was using the 240/350 based hubs when they started their “wheelsystems” but they have switch a number of them except for the very high end ones to DT Swiss 360 prawl based hubs.

How can I make my bike wheels spin faster?

Quote from video: And what you're going to do is continue to do this another little trick is is you can use the you can use the spray cleaner and the propellant to make the bearings spin the grease out itself like.

How do you check rear wheel bearings?

Quote from video: Without any movement when the bearing is still shot making a noise and here's how I found a quick way to test it I spin it as fast as I can. And you hear that noise.

How do I adjust my hubs?

Quote from video: Tighten. Down the lock nut by hand onto the cone. If done right the axle will feel a little rough at this point. Now use your cone wrench to tighten the cone against the lock nut. It should be tight.

How do I adjust my axle hub?

Quote from video: Them is a case of opening the lever. And then. You may often find that you need to locate the back of the lever in a little recess on the axle. And that allows you to actually unscrew.

How do I fix the rear hub on my bike?

Quote from video: So put just a little bit of grease around the threads. There. And thread this on and it should just spin right on like that. And then I'll use the tool here fit this into there like this.

Does giant use Shimano?

All of Giant’s road bikes feature groupsets from Shimano and SRAM. The lower the number included in a bike name the higher the quality of the components. The TCR Advanced Pro Disc 1 has a higher spec than the TCR Advanced Pro Disc 2, for example, and the TCR Advanced Pro 0 Disc has a higher level again.

What do the numbers mean on Giant bikes?

Don’t be daunted by the numbers, they refer to the number of teeth on the crankset. A higher tooth count means the bike can push a bigger gear, making it faster for each pedal revolution.

How do I get rid of giant pr2 freehub?

Quote from video: Похожие запросы

How do you tighten a hub bearing?

Use one hand to turn the wheel slowly in its normal forward direction of travel, and tighten the hub nut to the correct torque with the other. Turn the wheel slowly while you tighten. Lower to tighten finally.

How tight should rear hub be MTB?

You want your rear axle very tight. 150 in/lb is about standard. If it is not tight it will allow the rear wheel to move around and it ties your rear triangle together. Basically the whole back of the bike will feel sloppy.

How much does it cost to tighten a bike hub?

Service Price: $55



Making sure the wheel hubs on your ebike are properly tightened is very important, as that is what rotates around as the wheel moves.

How do you fix a rear hub on a mountain bike?

Quote from video: So step one is obviously removing the rear wheel from your bike. You're gonna take your cassette off and I would recommend taking off the disk grater.

How do I fix the rear hub on my bike?

Quote from video: Today I'll be showing you how to repack clean and adjust the hub of a bicycle. This is the rear hub of my single feed.

How do I adjust my axle hub?

Quote from video: Them is a case of opening the lever. And then. You may often find that you need to locate the back of the lever in a little recess on the axle. And that allows you to actually unscrew.