How do you mount a dartboard?
7 min read
Asked by: Matt Mestas
More videos on YouTube
- Begin by marking off the proper height from the floor on your wall (5’8” or 1.73m). …
- Apply the metal Mounting Feet to the back of your dartboard, using the Stabilizer Screws. …
- Drive the Dartboard Center Screw into the pre-drilled hole, leaving space to hang the dartboard onto the Mounting Bracket.
How do you hang a dart board on the wall?
With the bracket that you just put. Up. You slide it down onto the bracket. Position it so the 20 is at the top of the dartboard. And then you'll be ready to start playing steel tipped darts.
How high do you mount a dartboard?
For these boards, the regulation calls for a setup height of 5 feet and 8 inches from the floor line to the center of the dartboard and bullseye. 7 feet and 9 ¼ inches should be the distance from the dartboard to the back of the throw line.
How do you place a dart board?
Dart Board Height: 5 feet. 8 inches from floor to the center of the bull’s-eye. Distance from front of the dartboard to the throwing line: Steel Tip: 7 feet 9 1/4 inches, Soft Tip: 8 feet 0 inches. To mark the throw line a simple piece of tape will suffice.
How do you secure a dartboard to a cabinet?
How to Hang a Dartboard in a Cabinet
- Take Measurements. …
- Locate the Mounting Holes on the Cabinet. …
- Locate the Wall Studs. …
- Mark the Spots for the Mounting Hardware. …
- Assemble the Mounting Hardware on the Cabinet. …
- Assemble the Dartboard Mounting Hardware. …
- Drill Mounting Holes. …
- Insert Anchor Sleeves or Screws.
How do you hang a dartboard without fixing it to the wall?
- How to Hang a Dartboard Without a Wall. Other options to mount a dartboard that does not include a wall are: …
- Freestanding Frame. A freestanding frame is suitable for any dartboard. …
- Freestanding Stand. …
- Portable Dartboard. …
- Dartboard Freestanding Cabinet. …
- Hang it on a Door. …
- In Summary.
- Insert a 5/32-inch carbide drill bit into a power drill for 3/16-inch masonry screws. Use a 3/16-inch carbide drill bit for 1/4-inch masonry screws.
- Drill pilot holes in the brick for each screw. …
- Remove the drill bit from the drill. …
- Drive the masonry screws into the brick at each pilot hole.
Can you mount a dartboard on drywall?
To hang a dartboard on drywall, it’s best to mount the board to a wall stud. The stud provides ample support for the dartboard’s weight. A board can weigh 10 pounds or more, enough to rip the mounting screws out of drywall if the board is hung from drywall without wall anchors.
What do you put behind a dart board?
A dart surround is a foam border that is cut precisely to fit around a dartboard. This offers immediate protection to your wall from any stray darts that misses the board. Most surrounds are only a few inches wide, so the protection they offer is limited.
How far is the line from a dart board?
7 feet 9 ¼ inches
Dartboard Distance for Throw Line – Horizontal
Steel tip dartboards: Horizontal distance is 7 feet 9 ¼ inches (2.37 meters). Soft tip dartboards: Horizontal distance is 8 feet (2.44 meters). It’s important to measure from the face of the dartboard, not from the wall.
What is the distance from dartboard to throw line?
7 feet, 9.25 inches
The official distance is 237cm (7 feet, 9.25 inches) from the front of your dartboard to the back of the throw line (aka Oche or toe line).
Will plasterboard hold a dart board?
Drywall (also known as plasterboard) is a budget-friendly alternative to more robust building materials. Most drywall will hold about 20lbs just with a basic nail in the wall. A dartboard is rarely heavier than 10 or 12 lbs but there are some caveats.
How do you fix a dartboard on a brick wall?
The Quick Answer. The best method of hanging a dartboard on a concrete or brick wall is to use a U-shape bracket. This allows you to position the board most securely and rotate it to make it last longer. Alternative methods of hanging a dartboard without nails include using command strips, brick clips or board stands.
Will command strips stick to brick?
Will Command™ Products stick to brick? No. Command™ Products are intended for mostly smooth surfaces such as those listed above. However, our products will stick to painted, smooth cinder block (the type found inside many school and office buildings).
How do you screw into brick?
How to Put Screws Into Brick
Is it better to screw into brick or mortar?
If the brick shows signs of old age through spalling and flaws, drilling into the mortar will be better. It’s also tricky to match the color of your brick when filling holes. Mortar is easier to drill through because it’s a softer substance than brick and is also easier to patch or repair.
Do you need special screws for brick?
To screw into brick there are only two things you need. Screw anchors for concrete ( Walldog, Tapcon, concrete screw, or screw anchors are all types of masonry screws) and a masonry drill bit. Those are the absolute basics.
Can you drill into brick without a hammer drill?
To drill into brick without a hammer drill, you can use the masonry or concrete drill bits as an alternative option. You can also utilize an impact driver if it’s within your reach.
Can a cordless drill go through brick?
A standard cordless drill has numerous applications when it comes to our home small projects, and surprisingly, it can be used to drill into stone or masonry.
Can a cordless drill go through concrete?
Can We Use Our Cordless Drill To Drill Concrete? Yes, you can. With proper technique and effort, you can use a cordless drill to drill concrete. Cordless drills these days come with a powerful motor and long-lasting batteries.
Why won’t my drill go through brick?
The most common reason a drill won’t penetrate a wall at all is because the drill is spinning in the wrong direction. If the drill bit enters the wall and then hits resistance, the typical cause is a metal plate or masonry obstruction.
What’s the difference between a hammer drill and a normal drill?
A hammer drill delivers more power in the form of a hammering action. The force of the hammer drill is applied directly to the bit. They are most commonly used for drilling in concrete and masonry. The hammering portion of this motion can be turned off, allowing the tool to function more like a standard drill.
How do you tell if my drill is a hammer drill?
When you look at a hammer drill, it has an additional hammer mode you can switch into. Some models have the mode changes separate from the clutch collar and others keep them all on one collar. Regardless, the hammer mode is almost always right next to the drill mode.
Do masonry drill bits go blunt?
Using the wrong drill bits – If you use all-purpose drill bits on abrasive materials like masonry or stone, their edges will become dulled and ineffective on metal or wood. Applying too much or not enough pressure – Too much pressure can break the bit, and not enough pressure can blunt the bit.
Should you use water when drilling into concrete?
Though you don’t need to water down the concrete, the water will help to collect and remove the drilling dust, which can be hazardous to your health and “clog” the drill bit. The water can also help to keep your bit from overheating, which in turn helps keep the bit from shattering.
Why does my Bosch hammer drill keep stopping?
It’s either some bad contacts on the battery connector as JPhi1618 said, or the control electronics are faulting out, in which case the drill is trash. I’d try pulling the battery and checking the contacts, maybe cleaning them with some electrical contact cleaner (you can usually find that at automotive stores).
