Broken Cogset-Back Wheel will not turn when pedaling
6 min read
Asked by: Michelle Rodriguez
Why is my bike back wheel not turning?
Quote from video: They just kind of stay stuck down and so when you pedal forward they just slip over the teeth. And the wheel doesn't turn. So in that case what you want to do is flush out the old grease.
How do you fix a broken freewheel?
Quote from video: Now ultimately what I would do is clean and lubricate the inside of the freewheel. And you might be possible do that on the wheel here. But I actually prefer to just take the freewheel off the wheel.
What do you do if your bike won’t pedal?
If the pedals on a bicycle won’t turn, it likely means the pedals or cleats are too worn to function properly. Fixing this particular problem typically means needing to completely replace the pedals and or cleats. However, it could also mean that the gears simply need oiling or cleaning.
Why is it hard to pedal my bike?
Make sure that each component is not too tight, loose, uneven, dirty or lacking lubrication. In most cases, the cause is something simple such as a dirty chain or increased chain tension. However, difficulty pedalling could also be the result of more severe damage, such as bent wheels.
Why is my hub not engaging?
Most likely you have old grease and/or grime which is causing the prawls to stick closed. Get the freehub off, remove the rubber seal, soak in degreaser, blow clean with an air compressor, relube with a light weight oil, ensure everything in the freehub is clicking again then reassemble your hub.
How does a freewheel work?
Mechanics. The simplest freewheel device consists of two saw-toothed, spring-loaded discs pressing against each other with the toothed sides together, somewhat like a ratchet. Rotating in one direction, the saw teeth of the drive disc lock with the teeth of the driven disc, making it rotate at the same speed.
What is the difference between freewheel and freehub?
Freewheel vs Freehub – Thread Differences
One of the main difference is that freewheels typically have a threaded hub. Bikes equipped with cassettes do not have a threaded hub, but instead, slip onto the hub with splines. But the differences, without getting too technical — go deeper than that.
How do you get a stuck freewheel off?
Quote from video: So I'm going to show you the trick to get those off. This particular one uses a Shimano tool with splines.
How do you remove a rear freewheel?
Quote from video: Turn the tool counterclockwise. It may take a good bit of force to loosen the freewheel from the hub. After it's loose remove the axle nut or skewering. That continue to unthread the freewheel.
How do you unlock bike pedals?
Quote from video: Put all your weight downwards. And there's nothing below that if it suddenly comes loose you're going to hit your handle anything hold it solid put your weight on the spanner. And it should loosen.
What is a bicycle freewheel?
The freewheel is a block of cogs that screws directly onto threads on the rear wheel. There is no need for it to be mounted onto a hub. It typically comes with anywhere between 1 to 7 cogs, and it is rare to find a freewheel on a modern bike. You do however find them on some new single-speed bikes.
What’s the difference between a freewheel and a cassette?
The freewheel is a single-unit and the act of pedaling tightens the freewheel to the hub. Whereas the cassette hub is a set of gears (cogs) that slides onto a cassette and is held in place by a lock ring.
How do you engage a freewheel?
Quote from video: You're able to easily move it or someone else is able to easily help you move it to re-engage the freewheel you're just going to pull down on the lever.
How do I know if my freehub needs replacing?
Check the freehub for wear to see if it needs replacing or just cleaning and relubing. To do this, firmly grab the splined body and give it a wiggle. If it moves more than a couple of millimetres side to side, replace it. Otherwise, a good clean and oil will do fine.
How do I fix the rear sprocket on my bike?
Quote from video: You want to fit the flat side against the sprocket. Put the lock ring on and tighten it by hand at first before using the lockring. Tool.
How long should a bike wheel spin freely?
You should be getting more than 10 seconds. One test for excessive drag is to watch the wheel as it stops spinning. It should oscillate back and forth two or three times as the heaviest section of the wheel settles to the bottom.
What is a wheel bearing?
What is a wheel bearing? And what does it do in a car? A wheel bearing is a crucial part of the wheel assembly that connects the wheel and the axle. It is a set of steel balls (ball bearings) or tapers (tapered bearings), held together by a metal ring. It enables the wheel to rotate smoothly with a minimum of friction.
How do you loosen the brakes on a bike?
Quote from video: It's not hitting on this either space on the side. So you can loosen this side I'm sorry tighten this side a little bit to bring it this way. Or you can loosen this side also to bring it that way.
What is a bicycle freewheel?
The freewheel is a block of cogs that screws directly onto threads on the rear wheel. There is no need for it to be mounted onto a hub. It typically comes with anywhere between 1 to 7 cogs, and it is rare to find a freewheel on a modern bike. You do however find them on some new single-speed bikes.
What does a freewheel look like?
Quote from video: It has the spinning mechanism built into the cluster. This one the spinning mechanism freehub body is built on to the hub. And on to that that wheel setup.
What is the difference between a freewheel and a freehub?
Freewheel vs Freehub – Thread Differences
One of the main difference is that freewheels typically have a threaded hub. Bikes equipped with cassettes do not have a threaded hub, but instead, slip onto the hub with splines. But the differences, without getting too technical — go deeper than that.